This package is used inside the control panel to force 2011 edition Funduino duemilanove 2009 ATMEGA 328P development board, with some other common version is quite different!
Following is a brief look at 2011 to force version funduino advantages:
To force version of the improvements:
1 LED more ergonomic
Arduino board four original LED are designed in-house, less ergonomic, there are many experimenters often twisted neck, because as long as the plug expansion board , we should get down view LED . We therefore based on the most advanced UNO32 solutions, these four LED are moved to the front of the board, to facilitate observation of the experiment .
2 more convenient analog input ( output out )
Arduino servos and sensors, each connected to almost every Canadian to buy an expansion board, but also a bunch of wires , for which we are attentive to all analog inputs ( can output _ It uses 14 ~ 19Pin setting )gave the Vcc Gnd , so the plug can be used immediately ( but please be careful polarity _ it's negative .positive . signals )
3 more convenient PWM output
in PWM or do some expansion , RELAY infrared receiver , temperature measurements, our board also provide you with a cozy six PWM ( or I / O) ( but please be careful polarity _ its signal . positive .negative ) terminal pin. Taking into account the stability so we pay more for you at the cost of the two regulators capacitor , so that will be more stable ( can also be coupled with expert larger capacitance )
4 increased power and ground pin
current when we want to access to power, it is often not enough , for example, is sometimes necessary to use a logical pen, when there is no place better clip. So we do not affect any function under the premise, more power pin ( if you do not use, you can add short sleeve, to prevent contact with the top of the expansion board and shorted )
5 increase the width of copper foil, increase stability
experienced customers and sharp-eyed master, will notice this in Arduino traces are as wide as possible a number. Coarse alignment, when you use an instant fast output changes, the waveform will still pretty many . Its structure will come a lot safer , because we have found that some manufacturers dropped Arduinocopper platinum easy to break, so it hard to make this improvement .
6 supercharged 3.3v maximum current
Arduino using FT232RL the 3.3V output supply, the maximum output current is only about 50mA , encounter large current needs of 3.3 module, you will have enough power. Therefore, we use the ASM1117-33 Output 3.3Vpower supply , current 1000mA back you accept SD card 3G_Sensor Zbee wii chicken etc. 3.3V device, as long as the fingertips can be your all I / O pins have become 3.3V smart players, we know that this way save4050 's IC and resistor divider, but also save wiring time.
7 space can be expanded to increase
our central plank aside two holes, in accordance with your needs plus a large capacitor ( capacity does not mean bulky ) or 2.54/2PIN terminal , reserved for your unlimited imagination space.
8 to increase the quality control
of our board have strengthened quality control, each board will have a person responsible for the detection and signature confirmation, but also for the factory serial number are on the record in order to better ensure that your rights.
2011 to force version Tutorial Outline
2011 Edition Starter Kit to force the list
1.Funduino 2011 to force the control panel 1 a
This package is used inside the control panel to force 2011 edition Funduino duemilanove 2009 ATMEGA 328P development board.
2 prototype open hair extension board 1 a + MINI breadboard one.
3 breadboard a one
Set inside using a $ 17 value
Advanced bread board, http://item.taobao.com/item.htm?id=12281568551 &, is not the kind of a few dollars.
4.10 * 20CM, 2MM thick transparent plexiglass plate an easy experiment circuit equipped, you can also do the smart car chassis, do both.
5 large component box a
Kit component box we are using the new Pengcheng double shatterproof component boxes, focus on brand and quality.
6 SMD component box a
Add a rectangular box chip components to facilitate the placement of tiny materials.
7.LED lights red yellow and green of the five months
8 Buzzer 2 months
9 button switch 4 months
10 digital tube 2 months
11. Mercury switch two, sometimes replaced with ball switch
12 photoresistor 3 months
13 adjustable resistance a
14 flame sensor 1 a
15 infrared receiver tube 1 a
16 Resistor 220 Ohms, 1K , 10K each 5 months
17.LM35 temperature sensor 1 a
18.USB line 1 of
19 colorful bread line 20 of
20.9V Battery + battery box 1 a
21.mini Remote Control 1 a
22 Essentials a copy (electronic files)
* 세금계산서 발행방법은 게시판 공지사항 참조.
* 기술문의는 이메일(master@toolparts.co.kr)로 문의.
전자부품 특성상 제품에 이상이 있거나, 상품정보와 상이한 경우 외 에 단순 고객변심으로는
교환 반품이 불가능 합니다 구매전 이점 유의해 주세요!!!
고액결제의 경우 안전을 위해 카드사에서 확인전화를 드릴 수도 있습니다. 확인과정에서 도난 카드의 사용이나 타인 명의의 주문등 정상적인 주문이 아니라고 판단될 경우 임의로 주문을 보류 또는 취소할 수 있습니다.
무통장 입금은 상품 구매 대금은 PC뱅킹, 인터넷뱅킹, 텔레뱅킹 혹은 가까운 은행에서 직접 입금하시면 됩니다.
주문시 입력한 입금자명과 실제입금자의 성명이 반드시 일치하여야 하며, 7일 이내로 입금을 하셔야 하며 입금되지 않은 주문은 자동취소 됩니다.
교환 및 반품이 가능한 경우
- 상품을 공급 받으신 날로부터 7일이내 단, 가전제품의
경우 포장을 개봉하였거나 포장이 훼손되어 상품가치가 상실된 경우에는 교환/반품이 불가능합니다.
- 공급받으신 상품 및 용역의 내용이 표시.광고 내용과
다르거나 다르게 이행된 경우에는 공급받은 날로부터 3월이내, 그사실을 알게 된 날로부터 30일이내
교환 및 반품이 불가능한 경우
- 고객님의 책임 있는 사유로 상품등이 멸실 또는 훼손된 경우. 단, 상품의 내용을 확인하기 위하여
포장 등을 훼손한 경우는 제외
- 포장을 개봉하였거나 포장이 훼손되어 상품가치가 상실된 경우
(예 : 가전제품, 식품, 음반 등, 단 액정화면이 부착된 노트북, LCD모니터, 디지털 카메라 등의 불량화소에
따른 반품/교환은 제조사 기준에 따릅니다.)
- 고객님의 사용 또는 일부 소비에 의하여 상품의 가치가 현저히 감소한 경우 단, 화장품등의 경우 시용제품을
제공한 경우에 한 합니다.
- 시간의 경과에 의하여 재판매가 곤란할 정도로 상품등의 가치가 현저히 감소한 경우
- 복제가 가능한 상품등의 포장을 훼손한 경우
(자세한 내용은 고객만족센터 1:1 E-MAIL상담을 이용해 주시기 바랍니다.)
※ 고객님의 마음이 바뀌어 교환, 반품을 하실 경우 상품반송 비용은 고객님께서 부담하셔야 합니다.
(색상 교환, 사이즈 교환 등 포함)